888812404260455644556

X-908 Infini2 – next level Infinity-Mirror

X-908 Infini2 – next level Infinity-Mirror



An infinity mirror in the front illuminated by RGB LEDs, an RGB LED strip in the power supply tunnel and three 120mm RGB fans make the X-908 Infini2 a real eye-catcher. The front made of tempered glass and the side panel made of 4mm thick tempered glass give a generous insight on strong effects and colors, which can be managed by a switch on the front or via the 5V RGB header connector (addressable RGB LEDs).

The control panel of the X-908 Infini2 is equipped with HD-Audio jacks, two USB 3.0 Type A and two additional USB 3.0 Type C ports and is easy to reach. Two separate switches provide the option of manual fan control in three levels (Low, High or Stop). The power and reset switches are slightly recessed, preventing accidental operation in the dark.
The infinity mirror is set in scence through the tempered glass of the front panel, offering insights into the depths of the optical illusion. Another highlight is the 4mm thick tempered glass side panel, which additionally highlights the built-in hardware. Through the side-mounted RGB LED switch all the pre-programmed effects and colors can be switched easily and conveniently. With the 3-pin RGB header connector for 5V RGB motherboard controls and matching motherboard software, all RGB LEDs can also be individually controlled (addressable RGB LEDs).
In the top of the case is a large-area dust filter, which protects the interior of the case from dust. With two simple clicks, the dust filter is removed and can be cleaned easily and quickly.
Three standard mounted 120mm RGB LED fans not only skilfully show off the interior, they also ensure clean and cool air for the installed components. The effects of the fans can be controlled via the built-in RGB LED switch or the 3-pin RGB header connector for 5V RGB motherboard controls, synchronous with the RGB LEDs in the front and in the power supply tunnel.
Behind the motherboard carrier is the heart of the X-908 Infini2 - the RGB / PWM board. Over the board, all built-in RGB LEDs, such as the RGB LEDs of the fans, the RGB LEDs of the LED strip above the power supply tunnel or the RGB LEDs of the infinity front panel, will be synchronously controlled. In addition, up to five 3-pin fans can be connected there, which can be all speed-controlled via the PWM connection of the mainboard. Two slots for 2.5" SSDs find their place on the back of the mainboard tray.
  • Front panel made of tempered glass with RGB Infinity-Mirror
  • Window side panel made of 4mm thick tempered glass
  • Three 120mm RGB fans and RGB LED-strip
  • 3pin RGB header connector for 5V RGB motherboard control
  • Front panel made of tempered glass with RGB Infinity-Mirror
  • Window side panel made of 4mm thick tempered glass
  • Three 120mm RGB fans and RGB LED-strip
  • 3pin RGB header connector for 5V RGB motherboard control

Learn more!

To learn more about the features and details of the X-908 Infini2, just click on the magnifying glasses.

SSD-Holder

2.5" HDD-Trays

The mounting frames provide space for two 2.5" hard drives at the back of the mainboard tray.

RGB-/PWM-Platine

RGB / PWM board

Over the switch in the front or via the 3pin 5V RGB header connector (addressable RGB LEDs), up to five RGB devices can be managed over the board.

HDD Holder

Hard drive mounting frames

Two removable mounting frames provide space for either a 2.5" or 3.5" hard drive.

Beneath the two bays you can install another 3.5" HDD frameless.
Dust Filter

Power supply frame

The power supply frame protects against annoying vibrations from the power supply and also offers a removable dust filter on the bottom.

SSD Plate

2.5" mounting

Installation of the 2.5" HDDs in the interior.

GPU Holder

Graphics card bracket

The included graphics card holder supports overlong and heavy graphics cards and hold them in position.

RGB Fan

RGB fans

Three 120mm RGB fans (1x rear, 2x top) are installed as standard and can be controlled synchronously via the RGB LED switch or the 3pin 5V RGB header connector (addressable RGB LEDs).

LED Strip

RGB LED strip

A standard RGB LED strip in the power supply tunnel can also be controlled synchronously with the RGB fans.

Feder

Silk touch coating

The interior is covered with a high-quality silk touch coating and thus upgrades the X-908 Infini2 additionally.

  • SSD-Holder

    2.5" HDD-Trays

    The mounting frames provide space for two 2.5" hard drives at the back of the mainboard tray.

  • RGB-/PWM-Platine

    RGB / PWM board

    Over the switch in the front or via the 3pin 5V RGB header connector (addressable RGB LEDs), up to five RGB devices can be managed over the board.

  • HDD Holder

    Hard drive mounting frames

    Two removable mounting frames provide space for either a 2.5" or 3.5" hard drive.

    Beneath the two bays you can install another 3.5" HDD frameless.
  • Dust Filter

    Power supply frame

    The power supply frame protects against annoying vibrations from the power supply and also offers a removable dust filter on the bottom.

  • SSD Plate

    2.5" mounting

    Installation of the 2.5" HDDs in the interior.

  • GPU Holder

    Graphics card bracket

    The included graphics card holder supports overlong and heavy graphics cards and hold them in position.

  • RGB Fan

    RGB fans

    Three 120mm RGB fans (1x rear, 2x top) are installed as standard and can be controlled synchronously via the RGB LED switch or the 3pin 5V RGB header connector (addressable RGB LEDs).

  • LED Strip

    RGB LED strip

    A standard RGB LED strip in the power supply tunnel can also be controlled synchronously with the RGB fans.

  • Feder

    Silk touch coating

    The interior is covered with a high-quality silk touch coating and thus upgrades the X-908 Infini2 additionally.

    • Hauptbild
      Frontal
      Vorne rechts
      Rückseite
      Innenraum offen
      Innenraum offen mit RGB-Netzteil
      Mainboard Rückseite
      Top geschlossen
      Top offen
      Detail Schalter
      Staubfilter
      HDD-Frames
      GPU-Halter
      RGB-Lüfter
      RGB-Platine
      HDD-Träger leer
      HDD-Träger mit 2.5
      HDD-Träger mit 3.5
      RGB Kabel
      USB 3.0 -> 2.0 Adapter
      GIF
    • Size
      Form factor eATX, ATX, μATX, ITX
      Dimensions (h/w/d) 530 x 210 x 510mm
      Installation Dimensions
      Height CPU cooler (max.) 160mm
      Length graphics card (max.) 420mm
      Drive Bays
      5.25" external
      3.5" external
      3.5" internal 3x¹
      2.5" internal 6x¹
      Front connectors
      USB 3.0 2x
      USB 3.0 Type C 2x
      Microphone 1x
      Headphones 1x
      Power supply
      ATX-PSU
      Fan mounting option
      Front 2x 120mm (optional)
      Top 2x 140mm or 2x 120mm (2x 120mm serial, RGB, 3pin-connector)
      Rear 1x 120mm (serial, RGB, 3pin-connector)
      Guarantee / Warranty
      Warranty 24 months
      Scope of delivery & Features
      Scope of delivery

      Case

      Retail packaging

      Screw set

      RGB sync cable

      Adapter USB 3.0 to USB 2.0, internal

      Graphics cards bracket

      Manual (German)

      Features

      Front panel with Infinity-Mirror-Effect made of tempered glass

      Window side panel made of 4mm thick tempered glass

      Integrated RGB LED-Strip on the PSU tunnel

      3x 120mm serial RGB fans in the top and rear

      RGB-/PWM-board for up to 5 RGB-devices
      (in combination with mainboard with PWM function up to 5 fans with 3pin-connector)

      3pin RGB header connector for 5V RGB motherboard control

      Two separate controllers for once 2 fans and once 1 fan with 3pin connection for speed control

      Two 3.5" mounting options underneath the mainboard tray with separated airflow

      Two SSD-mounting options on the rear of the mainboard tray

      Option to mount liquid coolers in 120mm and 240mm

      Easy removable dust filters in the cap and the bottom

      Decoupled PSU mounting in separated tunnel at the bottom

      Cage with high quality silk touch coating

      Cable management

      USB Type C internally as USB 3.0 connector

      Stands

      Logistical data
      Shipping Unit 1 Pcs
      EU palett 12 Pcs
      Weight net = 11.78kgs
      gross = 13.66kgs
      Item number 88881240
      EAN-Code 4260455644556
      ¹ = can vary by using several mounting options
    •   No further information is available for this product.

    •   No special accessories are available for this product.

    •  
       
       
       

        This product has not received any awards yet.

    Contact

    • Our office hoursMO - TH  8:30 AM - 5:30 PMFR  8:30 AM - 3:00 PM
    • +49 (0) 511 726678-30
    • +49 (0) 511 726678-37
    • vertrieb@inter-tech.de

    Copyright © 2019 Inter-Tech GmbH. All rights reserved. Designed by R. Lautenschläger
    Copyright © 2019 Inter-Tech GmbH. All rights reserved. Designed by R. Lautenschläger
    Copyright © 2019 Inter-Tech GmbH. All rights reserved. Designed by R. Lautenschläger

     

    The products marked with ® are registered trademarks of their respective companies. The products marked with ™ are trademarks of their respective companies.

    The products marked with ® are registered trademarks of their respective companies. The products marked with ™ are trademarks of their respective companies.